Real Auto Mechanic's Guides and Recommendations.
Home / LDV / Cub /

How to repair dust cap on LDV Cub

Suspension Technician
Christopher Young
Interesting how to install dust cap in your automobile, you can see the quick tutorial how to install dust cap easy and efficient way!

Do LED headlights need ventilation on a LDV Cub?

Do you have adequate venting? Unlike conventional halogen bulbs, the diodes in LED bulbs will not produce a lot of heat even under extreme or continuous usage. However, the bottom part of the bulbs are the ones that need to vent out heat.

How do you know if a speaker is damaged on a LDV Cub?

The most common aural indication of a blown speaker is an unpleasant buzzing or scratching sound, by itself or roughly at the pitch of the note the speaker is attempting to reproduce. Or there could be no sound at all.

Does dust affect subwoofer?

Dust,not a major problem,as long as you do not have thick layers. Breathing dust is bad,and we know subs move air and will also move... dust. Better have a dust free room in any case.

How do you remove a 2018 LDV Cub grease gun tip?

How to remove a grease gun from a grease nipple. - Okay what we're doing here today we're going to demonstrate how to attach and remove the grease gun from a grease nipple on a greasable ball joint. Basically you press firmly until it engages and then.

What is a speaker diaphragm on a LDV Cub?

In a dynamic loudspeaker, a diaphragm is the thin, semi-rigid membrane attached to the voice coil, which moves in a magnetic gap, vibrating the diaphragm, and producing sound. It can also be called a cone, though not all speaker diaphragms are cone-shaped.

What size is a standard valve stem?

The most common size we all know on our cars. This hole size is for use with rubber stem ("TR13") or the metal stem ("TR11") valved inner tubes. - 16 mm (0.635") diameter , the largest of the sizes.

When should you replace Bearing Buddies on a LDV Cub?

  1. Remove hubs and check the bearings before installing Bearing Buddy®. Replace bearings if they are damaged, rusted, or pitted
  2. Hold the Bearing Buddy® against the hub with a small block of wood, and drive it into place with a hammer
  3. Bearing Buddy® is held in the hub by an interference fit

How do you open the gas tank on a LDV Cub?

Luckily, it's pretty simple. All you need to do is simply press on the gas cap's cover like a button, and it should open right up. Hope that helps!

How do I know my valve stem size?

In most cases, adding 15mm to the height of the rim is a reasonable rule of thumb when it comes to deciding on a valve length. That extra 15mm is important because it provides enough length to fit any pump head.

How do I put an axle cap on on a LDV Cub?

Position the new end cap over the axle and center of the wheel. Push the end cap over the axle until it snaps into position. If more pressure is required, take a piece of cardboard or piece of wood and position it against the end cap. Then take a hammer and gently tap against it to snap the end cap into place.
If you feel that something wrong with information above, so warn us about that!
Post your comment


Comments on how to fix dust cap on a LDV Cub:
Blayne
How much does these bulb cost
Ra'id
Wow, I'm a bit surprised to hear that having no dust cap doesn't make a whole lot of difference. Especially in sealed box speakers! Essentially you're making the speaker ported in some sense, when the cap is missing. How can this not affect the sound? Also in ported speakers, the sound would change if you add another hole to the box. I guess I'd have to try to find out, I just don't have a speaker lying around right now to try it O:-)
Sebastiano
Dust caps are not snake oil. They serve a protective and performance purpose. Less cone area means less SPL and interference patterns at the center of the cone are not good for the audio fidelity.
Gilberto
entendi la referencia en el titulo edit:dust man se puso ese nombre por que le gusto el personaje de dustman
Mairead
Searcy, AR this weekend October 20th and 21st, event center off Queens Way Blvd.
Argyle
i Got a Woofer Excactly like this From a Flea Market for 10 Bucks...it was Pretty Decent
Maura
Very good score
Risto
what would happen if you had an cap that was flat and was the same size of the speaker inside
Emil
Prolly the bba
Talmadge
LOL ppl who think blowing a dust cap off 'blows your sub' Effin tards...The sub is still kicking to this day...Oh and facktards they are 15's and they do hit 154.4 ;) You all fail at life =)
Reaves
can i insert it in i20 asta
Bors
whats is the name of the song
Rahul
I'm a big fan!! can you do a review on a Harmony Audio HA-ML151? I would greatly appreciate it.
Jethro
wow...that was cool
Davet
cool I never did a speaker cone repair before thanks.
Stacey
lol nice^^
Roger
Maine nayi creta li hai kaafi confused hoon lagwau ki nahi
Rich
I have a pair of clones of this monitor.  Can you do me a favor and measure the diameter and length of the port tube?  Thanks in advance!
Abdul- Rashid
waste of money and time
Cord
outside shot after install?
Gaile
Bhai 35w thik rahegi ya 55w Plz reply
Creighton
If you are doing a lot of these, find a piece of pipe that fits over and hits against that same surface.
Drugi
its the same motor and basket as a tezla 2.0
Sproule
I just used a heat gun and made mine bubble out about another inch and it works great
Fajr
thank you sir for clarifying that (3
Jori
I feel that the dust cap provides more surface area on the cone itself and helps with rigidity, increasing overall efficiency
Tayson
Hi Jim, watched Video 253 on adjusting the Speed Adjustment Latch Assembly (Shift Plate). It was exactly what I needed. You're a great help to those of us who are still hanging on to our Snapper Riders. No Zero turn for me. Thanks for all you do for us.
Nann
Im going to the bank today i should have the money for them around monday
Lucian
Makes sense. Air doesn't attract dust. Hydraulic fluid, on the other hand...