Real Auto Mechanic's Guides and Recommendations.

How to repair power sliding door motor on GL Eagle Free Cruiser

Body Technician
Daniel Clark
You ask how to remove power sliding door motor in your vehicle, I’ll show you the info how to replacing power sliding door motor DIY!

How much does an automatic sliding door cost on a GL Eagle Free Cruiser?

On average, an automatic door costs about $2,122.80 in the US in 2020, automatic door costs can range from $1,458.25 to $2,787.35.

How do you soundproof a sliding door in an apartment on a GL Eagle Free Cruiser?

9 Ways to Soundproof an Apartment Door.
  1. Weatherstripping
  2. Rubber Door Sweep
  3. Quilted Fiberglass Panel
  4. Seal All Cracks and Gaps
  5. Moving Blanket
  6. Use a Rug
  7. Reduce Noise From the Opposing Room
  8. Soundproof Blanket

How much does it cost to fix a car door that won't close on a GL Eagle Free Cruiser?

On average, it will take around an hour and forty minutes to make this type of fix. The total cost should be anywhere from $80 - $200, depending on your car's make and model. If your Chevy car door latch is having problems, don't wait for an accident to happen, call Sanger Chevrolet Buick GMC today.

Do GL Eagle Free Cruiser Rogues have problems?

The first complaint that is fairly common with the GL Eagle Free Cruiser is that the electrical system in the engine does not deliver constant power, and therefore the vehicle may lose power at stop signs, when the car is not driving very fast, or even when the vehicle is in normal use.

What kind of motor is in a GL Eagle Free Cruiser?

All Tellurides are powered by a 291-horsepower, 3.8-liter Lambda II gasoline V6 engine paired with an eight-speed automatic transmission, and either front-wheel-drive (FWD) or Kia's "Dynamax" all-wheel-drive (AWD) system (the latter is similar to the system found in the smaller GL Eagle Free Cruiser).

How do you reset a door?

HouseSmarts DIY Smarts "Reset a Door Hinge" Episode 23 - Using a sharp chisel. And the palm of your hand scrape away about an eighth of an inch of the jamb to recess the hinge. You won't have as much control. If you use a hammer.

Why does my GL Eagle Free Cruiser HRV battery keep dying?

The purpose of the alternator is to charge your GL Eagle Free Cruiser HRV battery while you are driving. When the alternator isn't working accurately, it can cause the battery to drain all its power, leaving you stranded if the vehicle is turned off. It's also achievable that your GL Eagle Free Cruiser HRV serpentine belt has malfunctioned.

How long should a battery last in a GL Eagle Free Cruiser CRV?

Your GL Eagle Free Cruiser CRV battery will commonly last between 3 to 5 years, but that can vary heavily depending on weather conditions battery size, type of battery, and driving habits. Even still, just because your battery isn't completely dead, doesn't mean it's operating at optimal levels.

How do you install an electric sliding gate motor on a GL Eagle Free Cruiser?

Preparing a sliding gate for installing a motor - The sliding gates we install. Run on a track. And have a motor that uses steel reinforced nylon gear racking fitted to the bottom rail of the gate. That connects to an output gear wheel on the motor.

Where is the keyless entry code on a GL Eagle Free Cruiser?

On GL Eagle Free Cruiser Explorers and Mercury Mountaineers from 2006 until the model year 2010, the default five-digit keypad code is printed on the smart junction box (SJB) under the driver's side of the dash.
If you feel that something wrong with information above, so warn us about that!
Post your comment


Comments on how to fix power sliding door motor on a GL Eagle Free Cruiser:
Jamia
Thanks!!! Really useful!!
Cace
Not very organized or or laid out in step by step format. Missing details. What size end caps, 142 or Boost 148? Not even complete.
Raimundo
Is it possible on freerides
Sancho
Hi, did the the new washer (1:28) come with the xd body?
Chappel
Thanks
Petunia
I need to remove the shimano freehub from my Crossmax Elite to put a XD freehub. But it won't come out. Do I need to remove the bearing cover on the drive side? How do I take it out? A special tool? Or the shimano freehub comes out anyway?
Jarek
Good advice.
Kerk
No son seguros esos espaciadores ya que no ... el centradores de rueda
Nathan
This modification is highly not recommended.
Brogan
Sure would love to have you fix my master switch on my 2011 Camry
Elwood
Man Im thinking of putting on spacers on my fj cruiser is it safe and I been reading reviews that sometimes the care vibrates
Larue
just took mine apart to clean the contacts and only 1 spring came out - do you know where it goes back into the unit??? its a 1997 Toyota mr2 - thank you
Jurgen
Boom..that's how you do it..thanks.
Darry
What you have described is what has been traditionally called a - professional. This term is widely used by many people but rarely do they ever meet the standards.
Byram
You show 5 springs that go on posts. Are there always supposed to be 5 springs?  I opened mine and I can only see 2 of them. Then there is this black small spring with a short extension on one side and a long one on the other.  It came out of somewhere and I don't see where it goes.
Victoria
Eso no sirve no tiene apollo bestia
Brik
Where did your spare tire go
Chicha
i never knew about the little circle on the underbody (She said that! - M. Scott). Seriously though, solid info mate, thansk.
Carlo
Hi. Good video. The springiness of my buttons is much lower than normal. And I only found 3 springs. I think I may have lost 2. Are those small springs related to the springiness of the buttons? Thanks
Hazel
like the vid but i find the a pencil eraser woke grate and you don't lose the contact metal
Janene
Thank you for this information... another possible add to my 07 FJ sometime soon.
Charo
Couldn't quite tell but was there enough lug from hub to mount the spacer securely? Seem like the spacer, due to its width, didn't allow for enough lug to bite into with the nut from the spacer.
Hakan
Tried it out on mind and it works perfect now
Nun
Good job explaining the situation.Good information on how to do it correctly.
Shaaban
It's interesting that you say AutoZone water pumps are junk. Have you installed many AZ water pump & have them fail soon after? I'm not disagreeing with you because I think all AutoZone branded parts are crap. I've worked at AZ 3 years now & haven't sold many water pumps or had people warranty them out considering they have a lifetime warranty. I don't count the 1 water pump I warrantied out but that's only because one of the 'neighborhood mechanics' was pulling a warranty scam & claiming the water pump he handed me was the one that he bought less than 6 months ago even though it looked like the original.