Real Auto Mechanic's Guides and Recommendations.

How to repair clutch release bearing on Santana PS10annibal

Transmission Professional
Mark Thomas
Wondering how to change clutch release bearing in your automobile, I’ll show you the review how to change clutch release bearing with no problem!

How far do clutch fingers travel on a Santana PS10annibal?

Single-disc clutches operate best with a gap of 0.150 inch while dual-disc sets require a gap of around 0.200 inch. Because the clutch fingers automatically travel toward the release bearing as the friction disc/s wear, an additional clearance of 0.050 inch is assigned to the dual-disc arrangement.

Can you drive with a noisy Santana PS10annibal clutch?

A noisy clutch release bearing might last a hundred more miles, or it might not, but that isn't a risk you should be willing to take. Why? Because the longer you drive with a faulty clutch bearing the worse the damage to your whole clutch system is going to be.

Is silicone lubricant good for bearings on a Santana PS10annibal?

Silicone lubricant can be used in the forms of an oil, which is non-reactive to most substances, maintains it's greasiness in extreme temperature conditions and does not oxidize, or a silicone spray which is not only water resistant, but also allows you to lubricate those hard to reach places like mechanisms or.

What happens when a clutch pedal is depressed on a Santana PS10annibal?

When the clutch pedal is depressed, it disengages the wheels from the engine so that the car can effectively shift gears without disturbing the rotation of the wheels.

Why does my clutch make a noise when I press it?

Worn Pilot Bearing: If you notice noise when you press the clutch pedal in, the most likely culprit is the pilot bearing, which will need to be replaced. Worn Release Bearing: Another possible cause of noise when pressing the clutch pedal in is the release bearing.

What is a clutch release bearing noise?

Whistling or whining from the clutch can be caused e.g. by the release bearing running off-center, an off-center input shaft, or a defective pilot bearing. On the other hand, rattling noises may be due to load alterations if clutch disks are furnished with preliminary dampers.

Why does my clutch make a noise when I release it on a Santana PS10annibal?

Noise that persists indicates that the release bearing is bad. If the noise is gone, the pilot bearing is bad. Bearing noise that occurs when releasing the clutch pedal to engage the clutch while in neutral, but goes away when the pedal is depressed, is caused by a bad transmission input shaft bearing.

How do you diagnose a bad Santana PS10annibal clutch release bearing?

Bad Throw-Out Bearing Symptoms
  1. Noise When Depressing the Clutch
  2. Clutch Pedal Vibrations
  3. Problems Shifting Gears
  4. Too Stiff of a Clutch
  5. Grinding While Shifting Gears (Even Though the Clutch Is Depressed)

How do I know if my clutch on a Santana PS10annibal pilot bearing is bad?

When a pilot bearing/bushing fails, a vehicle may exhibit:
  1. No release;
  2. The transmission may pop out of gear;
  3. Noise;
  4. Vibration; and
  5. Catastrophic failure of the transmission if not fixed

How do you replace a clutch throwout bearing on a Santana PS10annibal?

How to install the Throwout bearing / Release Bearing install Santana PS10annibal And so what you want to pay attention to is if you look at the throw out bearing it has a little peak to it. So you want that to be facing. This area and then as you slide the bearing.
If you feel that something wrong with information above, so warn us about that!
Post your comment


Comments on how to fix clutch release bearing on a Santana PS10annibal:
Crespin
This is the best damn video for this job better than what I have seen from the z community thank you so much for this this!!
Van Aken
parang ang hirap mag drive ng truck
Shanahan
I really apreciate you
Abbas
Okay kaayo boss
Jessy
I want to swap my ... DS4 N12 1.6L engine for Peugeot 307 2.0L engine. My question is will I need to change the ECU and the key set and the fuse box? Or do i need to reprogram my key?. There are similarity between the 2 engine, the sitting is perfect, I just want to have more information before proceeding. Thanks in advance
Erasto
A couple questions- did you pass on removing the starter? From your directions it sounds like you also left the transfer case attached, right? Did you drain the little bit of fluid from the transmission to lighten it up or just go with what you've got?? The flares are 10mm bolts and can help people find the clips for a decent price. 120k miles, original owner, annual water runs in the jeep- so I'm certain I'll be doing this soon. Thanks for the video!
Abdul-Razzaq
bhai mere paas 2010 model Alto hai usko main power steering Karna Hai Tu Kitna kharcha aayega
Jone
why he explains so simple. Thanks Chrisfix!
Leonarda
A couple things the video doesn't mention, unless I missed it is clutch finger adjustment, or measuring runout on the flywheel. Also, if your going to go through the arduous task of splitting a tractor of this age it would probably be a good idea to replace the rear main seal too. Good video however thanks.
Oria
very interesting video, take care and stay safe kapatid
Macbeth
Ingat always idol godbless ganda pahiram ng sasakyan sir idol
Doane
did you cure that? i have the same problem.
Subhan
... tatambay muna ako dito at tatapusin ko ito hangganh dulo at unahan na rin kita at ikaw na bahala bumisita sa bahay ko salamat
Corrie
Ah yes that old what parts do I have that'll work trick. Much more fun than going to get new parts. I'm glad it worked out for you.
Storme
Hey, very nice video and the information in it is great with detals and everything. I just have one question: What is the difference between Spline Lubricant and vaseline? Can they be replaced with eachother?
Pin
How to reset po boss check engine light
Amani
Extend bleeder line up to where your reservoir the you can watch fluid level without get up and down to bleed
Jeneva
Replaying wafu host
Jody
Ingat lage kapatid
Cyntia
Thank you Lee for this video. I used it today to help me replace the clutch and bearings on my 2009 Wrangler. It was a huge help! Thanks!
Erle
Tusluk n po
Yasmine
Really glad I found this video (as well as the others you've made) - so many mechanics here are doing things terribly wrong.
Whistler
For the Ford 2000, just to replace the clutch, what is the approximate cost? (parts and labor)